Warning
Any electrical work should be performed only by a suitably trained and qualified automotive technician with qualification applicable to your country/ region/ state; and with an expertise in installing and troubleshooting advanced onboard components, including multiplexed circuits. Lytx, Inc. disclaims all responsibility for any damages arising from improper installation and maintenance of the device(s).
Read and follow the instructions and precautions in this guide and all documents referenced in this guide when installing the device(s). Always refer to the vehicle manufacturer’s service manual for proper installation and wiring of any aftermarket devices, including the Lytx device. Failure to do so may result in property damage and/or personal injury.
Warning
The device(s) interfaces with the vehicle’s electrical systems. However, it should not interfere with any of the vehicle’s electrical or operating systems. Lytx, Inc. disclaims all responsibility for any damages arising from improper installation and maintenance of the device(s).
Warning
Park the vehicle on a level surface before beginning any maintenance or installation. Block the wheels to prevent the vehicle from moving. Never work under a vehicle supported only by jacks as jacks can slip and fall over.
Warning
All wires that carry electrical current to the Lytx device(s) must be fused. Failure to fuse the constant power & Ignition wire can lead to serious personal injury and/or property damage. If any wire or cables containing fuse/fuse box need to be cut or otherwise shortened or extended, always be certain to replace such fuses/fuse box or install new ones.
Warning
Only approved wire connection methods are recommended. Refer to the vehicle manufacturer’s service manual to determine if sealing crimp connections, Add-A-Circuit, sealing butt connections, or OEM connections to open connection ports are approved. Never use plier tap products such as insulation displacement connectors (i.e., ScotchLoc connectors) when installing the Surfsight device(s) (unless mandated by the vehicle manufacture i.e., BMW).
Warning
Wire Protection: Take all necessary measures to protect all wire runs through a metal surface with a grommet or other device and all wire runs outside the vehicle cab with a loom. Always protect against wire fatigue and harness abrasion by properly attaching wires at closely spaced intervals, while avoiding contact with sharp edges or doing anything else that might result in exposed wires. All wires should be secured with tie wraps at least every one foot (30 cm/300 mm) or less. Do not over-tighten any tie wraps.
Danger
EXPLOSION HAZARD: Do not disconnect equipment unless power has been removed and the area is known to be non-hazardous. Comply with all EV/ non-ICE vehicle health and safety requirements. Do not disconnect equipment unless power has been removed and the area is known to be non-hazardous. Comply with all Electrically propelled/ non-Internal Combustion Engine vehicle(s). Health and Safety regulation within countries/regions/jurisdictions. Any electrical work on Electrically propelled vehicle(s) should be performed only by a suitably trained and qualified automotive technician to international level 1 EV qualification applicable to your country/ region/ state. Lytx, Inc. disclaims all responsibility for any damages arising from improper installation and maintenance of the Surfsight device(s).
Warning
Do not disconnect equipment unless power has been removed and the area is known to be non-hazardous. Comply with all Electrically propelled/ non-Internal Combustion Engine vehicle(s). Health and Safety regulation within countries/regions/jurisdictions. Any electrical work on Electrically propelled vehicle(s) should be performed only by a suitably trained and qualified automotive technician to international level 1 EV qualification applicable to your country/ region/ state. Lytx, Inc. disclaims all responsibility for any damages arising from improper installation and maintenance of the Surfsight device(s).
Warning
Substituting or supplementing components may impair suitability and performance. If you are missing any components contact Lytx Technical Support Center at 925.732.4246 or email support@lytx.com.
Warning
Use of correct Personal Protective Equipment to comply with any countries/regions/jurisdictions/ local company Health and Safety regulation for the installation site and type of installation being completed, to prevent serious injury, is the responsibility of the Installer and Installation partner. Wear safe eye protection to prevent serious eye injury when you perform vehicle maintenance or service.