Safety Instructions

Read and follow the instructions and precautions in this guide and all documents referenced in this guide when installing this device. Always refer to the vehicle manufacturer’s service manual for proper installation and wiring of any aftermarket devices, including the Lytx device. Failure to do so may result in property damage and/or personal injury.

WARNING: Park the vehicle on a level surface before beginning any maintenance or installation. Block the wheels to prevent the vehicle from moving. Never work under a vehicle supported only by jacks as jacks can slip and fall over.

WARNING: All wires that carry electrical current to the Lytx device(s) must be fused. Failure to fuse the power, ground, and ignition wires can lead to serious personal injury and/or property damage. If any wires or cables containing fuses/fuse boxes need to be cut or otherwise shortened, always be certain to replace such fuses/fuse boxes or install new ones.

WARNING: Wire Protection: Take all necessary measures to protect all wire runs through a metal surface with a grommet or other device and all wire runs outside the vehicle cab with a loom. Always protect against wire fatigue and harness abrasion by properly attaching wires at closely spaced intervals, while avoiding contact with sharp edges or doing anything else that might result in exposed wires. All wires should be secured with tie wraps at least every one foot (30 cm/300 mm) or less. Do not over-tighten any tie wraps.

EXPLOSION HAZARD: Do not disconnect equipment unless power has been removed and the area is known to be non-hazardous.

WARNING: Substituting or supplementing components may impair suitability and performance. If you are missing any components contact Lytx Technical Support Center at 925.732.4246 or email support@lytx.com.

WARNING: Wear safe eye protection to prevent serious eye injury when you perform vehicle maintenance or service.

WARNING: In order to reduce the potential danger of injuries, the driver and front passenger must always be correctly seated with seat belts correctly fastened when operating the vehicle.

DISCLAIMER: The Lytx device is a driver aid only, not a substitute for a safe, conscientious driver. The Lytx device cannot compensate for a driver who is distracted, inattentive or impaired by fatigue, drugs or alcohol. Whether or not the Lytx device is in use, it is always the responsibility of the driver to take appropriate corrective action. Never wait for the device to provide a warning before taking measures to avoid an accident. Failure to do so can result in serious personal injury or death or severe property damage. Always, it is the driver’s responsibility to:

WARNING: In certain conditions, including inclement weather, low visibility, certain road conditions (including poor lane markings, construction zones, dirt roads, heavy or complicated traffic, and curvy and winding roads), the Lytx device may have limited to no functionality. The Lytx device may not detect certain objects such as motorcyclists, bicyclists or pedestrians even in the most ideal conditions. Always keep the lens and view of the Lytx device unobstructed and properly calibrated so as not to inhibit function. Driving in certain conditions or any interference with the Lytx device can result in false, few or no warnings. The driver must always monitor traffic and surroundings and take measures to avoid an accident; failure to do so can result in serious personal injury or death or severe property damage.

WARNING: If the Lytx device is not functioning properly at any time, please contact your supervisor and have the device inspected immediately to correct the issue. Whether or not the Lytx device is functioning, it is the driver’s responsibility to maintain vehicle control; failure to do so can result in serious personal injury or death or severe property damage.

CAUTION: While cleaning the device or the vehicle cab, do not apply compressed air or cleaning solutions (such as Windex) to the Lytx device. Usage of these products may cause damage to the device.

WARNING: The optional livestream feature may have an approximate delay of 10 seconds. Livestream should never be used to assist the driver in operating the vehicle. The driver is responsible for the safe operation of the vehicle at all times and must always take measures to avoid a collision.

WARNING: Some countries/regions/jurisdictions have adopted, or may in the future adopt, laws that prohibit objects from being mounted on a vehicle’s windshield or other locations in a vehicle. Always refer to any applicable laws that concern mounting devices on vehicle windshields before choosing a mounting location. You are responsible for complying with such laws, as Lytx, Inc. does not accept responsibility for your failure to do so.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications to this product not expressly approved by Lytx, Inc. could void the user's authority to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

CAUTION: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son utilisation est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences susceptibles de provoquer un fonctionnement indésirable.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

CAUTION: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.

Pour se conformer aux exigences de conformité 102 RSS RF exposition, pour des configurations mobiles, une distance de séparation d'au moins 20 cm doit être maintenue entre l'antenne de cet appareil et toutes les personnes.

This device complies with the requirements of the following standard:

EN 301 908-1 V11.1.1—IMT cellular networks; Harmonized Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements.

This product complies with the requirements of the following standard:

EN 62311:2008—Generic standard to demonstrate the compliance of electrical apparatus with the basic restrictions related to human exposure to electromagnetic field (0Hz-300GHz)

This device has both E-Mark and CE Mark, in compliance with UNECE regulation E/ECE/TRANS/505/Rev.2.) This device may be installed throughout Europe and other regions that accept E-Mark or CE Mark as suitable proof of compliance. However, please note that regulations may vary per locality.

We, Lytx, Inc., hereby declare that the product listed below, to which this Declaration of Conformity relates, is in conformity with the Standards and other Normative Documents listed below:

Manufacturer’s Name & Address:

Lytx, Inc.

9785 Towne Centre Drive

San Diego, CA 92121 USA

Declares that the following product:

Product Name: Video Event Recorder Product Model:

The product specified above carries the marking, by complying with the essential requirements and provisions. Conformity is based upon the following standards:

Manufacturer’s Contact:

Lytx, Inc.

9785 Towne Centre Drive

San Diego, CA 92121 USA

Phone Number: (858) 430-4000

Fax Number: (858) 430-4001

EMC & Radio:

EMC Standard: AS/NZS CISPR 32:2013

EU Declaration of Conformity: 2006/42/EC The Machinery Directive

2014/30/EU The Electromagnetic Compatibility Directive

2011/65/EU The Restriction of Hazardous Substances Directive

Lithium Battery: IEC 60086-4:2014