Warning
Some countries/regions/jurisdictions have adopted, or may in the future adopt, laws that prohibit objects from being mounted on a vehicle’s windshield or other locations in a vehicle. Always refer to any applicable laws that concern mounting devices on vehicle windshields before choosing a mounting location. You are responsible for complying with such laws, as Lytx, Inc. does not accept responsibility for your failure to do so.
USA Federal Communications Commission (FCC) Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
The AI-14 dash cam (Model AI-14-010) wireless operation is safe and complies to RF Exposure requirements.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Caution
Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.
Canada – Industry Canada Notice
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
-
This device may not cause interference.
-
This device must accept any interference, including interference that may cause undesired operation of the device.
Caution
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
-
L’appareil ne doit pas produire de brouillage;
-
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Caution
Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.
Pour se conformer aux exigences de conformité 102 RSS RF exposition, pour des configurations mobiles, une distance de séparation d'au moins 20 cm doit être maintenue entre l'antenne de cet appareil et toutes les personnes.
Europe – Radio Equipment Directive 2014/53/EU (RED)
This device complies with the requirements of the following standards:
ETSI EN 301 908-1 V13.1.1(2019-11) – Transmitter Spurious Emission
ETSI EN 301 908-13 V13.2.0(2021-11) draft – Transmitter Spurious Emission
ETSI EN 301 511 V12.5.1(2017-03) – Radiated Spurious Emission
Radio Frequency Exposure
This product complies with the requirements of the following standard:
EN IEC 62311:2020 – Assessment of Electronic and Electrical Equipment related to Human exposure restrictions for Electromagnetic fields (0Hz-300GHz)
E-Mark and CE Mark
This device has both E-Mark and CE Mark, in compliance with UNECE regulation E/ECE/TRANS/505/Rev.2.) This device may be installed throughout Europe and other regions that accept E-Mark or CE Mark as suitable proof of compliance. However, please note that regulations may vary per locality.
Suppliers Declaration of Conformance
We, Lytx, Inc., hereby declare that the product listed below, to which this Declaration of Conformity relates, is in conformity with the Standards and other Normative Documents listed below:
Manufacturer’s Name & Address:
Lytx, Inc.
9785 Towne Centre Drive
San Diego, CA 92121 USA
Declares that the following product:
Product Name: AI-14 dashcam
Product Models:
-
AI-14-010, AI-14-011 (US/Can)
-
AI-14-036 - EU/RSA
-
AI-14-046 - MX/LatAm/Aus/NZ
The product specified above carries the marking, by complying with the essential requirements and provisions. Conformity is based upon the following standards:
Manufacturer’s Contact:
Lytx, Inc.
9785 Towne Centre Drive
San Diego, CA 92121 USA
EMC & Radio:
-
FCC Title 47 CFR Part 15 Subpart B
-
FCC Title 47 CFR Part 15.247
-
FCC Part 15 Subpart E
-
Industry Canada ICES-003, Class B
-
Industry Canada RSS-Gen
-
Industry Canada RSS-210 (applicable only to cellular modem variant)
-
Industry Canada RSS-247
2014/53/EU (RED) Radio Equipment Directive
2011/65/EU (RoHS) Restriction of the Use of Certain Hazardous Substances in E&E Equipment
EN 55032:2015: Electromagnetic compatibility of multimedia equipment